{"product_id":"v4-3-axis-gyro-for-drift-car-and-touring-drift-f1","title":"OmG V4 3-AXIS Gyro for Drift car and Touring Drift F1","description":"\u003cp\u003eV4 3-AXIS Gyro for Drift car and Touring Drift F1\u003c\/p\u003e\n\u003cp\u003e1.Working voltage: 5V-8.4V\u003c\/p\u003e\n\u003cp\u003e2.Consumption current: 6V 20mA≤\u003c\/p\u003e\n\u003cp\u003e3.Support input signal: PWM（50-333Hz）\/FUTABA S.BUS\/SANWA SSR\/SANWA SHR\u003c\/p\u003e\n\u003cp\u003e4.Output servo signal: 1520uS（333Hz）\/760uS(FUTABA SR)\/SANWA SSR\u003c\/p\u003e\n\u003cp\u003eControl system: PID control system\u003c\/p\u003e\n\u003cp\u003e5.End Point Adjustment Function:EPA\u003c\/p\u003e\n\u003cp\u003e6.Control Signal:SBUS\/PWM\u003c\/p\u003e\n\u003cp\u003e7.Receiver type:No restriction\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eV4 3-AXIS Gyro for Drift car and Touring Drift F1\u003c\/p\u003e\n\u003cp\u003eWorking voltage: 5~ 8.4V\u003c\/p\u003e\n\u003cp\u003eConsumption current:   6V   20mA≤\u003c\/p\u003e\n\u003cp\u003eWorking temperature: -10 ℃ + 50\u003c\/p\u003e\n\u003cp\u003eSupport input signal: PWM（50-333Hz）\/FUTABA S.BUS\/SANWA SSR\/SANWA SHR\u003c\/p\u003e\n\u003cp\u003eOutput servo signal:   1520uS（333Hz）\/760uS(FUTABA SR)\/SANWA SSR\u003c\/p\u003e\n\u003cp\u003eControl system: PID control system\u003c\/p\u003e\n\u003cp\u003eEnd Point Adjustment Function:EPA\u003c\/p\u003e\n\u003cp\u003eControl Signal:SBUS\/PWM\u003c\/p\u003e\n\u003cp\u003eReceiver type:No restriction\u003c\/p\u003e\n\u003cp\u003eDimension: 25*26*10mm  \u003c\/p\u003e\n\u003cp\u003eWeight: 12g  \u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eInstruction of Function Switch\u003c\/p\u003e\n\u003cp\u003e1.EPA(Travel Setting)\u003c\/p\u003e\n\u003cp\u003ePress the \"SW\" switch to power on,yellow LED blinks slowly.Entering to the servo travel setting,rotate the remote control steering wheel to make servo stop at the desired position(turn left\/turn right).Short press\"SW\" switch,yellow LED blinks 2 times quickly,red LED becomes solid,and green LED blinks slowly,it means current travel has been saved.Then rotate the remote control steering wheel to make the servo stop at the other desired position,short press the switch ,yellow LED blinks 2 times quickly,and then the yellow LED turns on,it means current travel has been saved as well.2 seconds later,the gyro will automatically enter into initialization mode,once completed,gyro is ready for use.\u003c\/p\u003e\n\u003cp\u003e2.Reset(Travel Restore Default Setting)\u003c\/p\u003e\n\u003cp\u003ePress the \"SW\" switch to power on and enter into the travel setting mode.After pressing and holding the switch for 3 seconds,the yellow LED starts to blinks alternately.Restore to default after 2 seconds. Then it will enter into initialization mode,once initialization is completed,the gyro is ready for use.\u003c\/p\u003e\n\u003cp\u003e3.Gain signal input or potentiometer adjustment is determined when the power is turned on. If loss of signal happened during using,the last signal is retained.\u003c\/p\u003e\n\u003cp\u003e4.Suitable for most of remote control systems,while plug in the gain wwire,it can adjust the sensitivity by transmitter;while do not plug in the gain wire,the gyro's potentiometer can be used for gain adjustment.\u003c\/p\u003e\n\u003cp\u003e5.Suitable for FUTABE S.BUS \u0026amp; SANWA SSR\u003c\/p\u003e\n\u003cp\u003e6.Adjust the gain via gain channel of transmitter(default for S.BUS input),the range if from -100%~0~+100%.\u003c\/p\u003e\n\u003cp\u003e7.While do not plug in the gain wire,the gyro's potentiometer can be used for gain adjustment,range from 0~100%.\u003c\/p\u003e\n\u003cp\u003e8.After powering on,press the SW for a while,LED2 flash(next to the SW),then short press the SW,and choose the direction of the X\/Y\/Z axis.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eLED Status Display\u003c\/p\u003e\n\u003cp\u003e3Axis LED\u003cspan\u003e\u003c\/span\u003eStatus\u003c\/p\u003e\n\u003cp\u003eRed quick flash           \u003cspan\u003e \u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003eInitialization\u003c\/p\u003e\n\u003cp\u003eYellow quick flash       \u003cspan\u003e \u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003eLoss of control signal\u003c\/p\u003e\n\u003cp\u003eGreen solid light         \u003cspan\u003e \u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003eSmall gain mode\/Gain signal input\u003c\/p\u003e\n\u003cp\u003eGreen slow flash         \u003cspan\u003e \u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003eSmall gain mode\/Potentiometer adjustment\u003c\/p\u003e\n\u003cp\u003eBlue solid light             \u003cspan\u003e\u003c\/span\u003eBig gain mode\/Gain signal input\u003c\/p\u003e\n\u003cp\u003eBlue slow flash             \u003cspan\u003e\u003c\/span\u003eBig gain mode\/Potentiometer adjustment\u003c\/p\u003e\n\u003cp\u003eYellow slow flash          Travel set mode\u003c\/p\u003e","brand":"GT Workz Singapore","offers":[{"title":"Purple","offer_id":48822262169852,"sku":null,"price":66.0,"currency_code":"SGD","in_stock":true},{"title":"Red","offer_id":48822262202620,"sku":null,"price":66.0,"currency_code":"SGD","in_stock":false},{"title":"Black","offer_id":48822262235388,"sku":null,"price":66.0,"currency_code":"SGD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0789\/2143\/3340\/files\/ABUIABACGAAgpqSBrwYo4Ka2ugEwoAY4oAY.jpg?v=1772690405","url":"https:\/\/gombakteamworkz.com\/products\/v4-3-axis-gyro-for-drift-car-and-touring-drift-f1","provider":"GT Workz Singapore","version":"1.0","type":"link"}